?005 fairchild semiconductor corporation 1 www.fairchildsemi.com october 2005 fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 4-pin full pitch mini-flat package random-phase triac driver output optocouplers features compact 4-pin surface mount package (2.4 mm maximum standoff height) p eak blocking voltage 250v (fodm301x) 400v (fodm302x) av ailable in tape and reel quantities of 500 and 2500. applicable to infrared ray re?w (230? max, 30 seconds.) bsi, csa and vde certi?ations pending ul (file# e90700) certi?d applications industrial controls tr af? lights v ending machines solid state relay lamp ballasts solenoid/valve controls static ac power switch incandescent lamp dimmers motor control description the fodm301x and fodm302x series consists of a gaas infrared emitting diode driving a silicon bilateral switch housed in a compact 4-pin mini-?t package. the lead pitch is 2.54 mm. they are designed for interfacing between electronic controls and power triacs to control resistive and inductive loads for 115v/240v operations. pa ck ag e dimensions 0.287 (7.29) 0.248 (6.30) 0.020 (0.51) 0.012 (0.30) 0.169 (4.29) 0.154 (3.91) 0.173 (4.40) typ 0.035 (0.89) 0.012 (0.30) 0.008 (0.20) 0.000 (0.0) 0.100 (2.54) ty 0.026 (0.66) p 0.033 (0.85) 0.026 (0.65) 0.094 (2.39) 0.079 (2.01) pin 1 note all dimensions are in inches (millimeters) 1 2 4 3 main terminal main terminal anode cathode
2 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers absolute maximum ratings (t a = 25? unless otherwise speci?d) electrical characteristics (t a = 25?) individual component characteristics t ransfer characteristics (t a = 25?) isolation characteristics * all typicals at t a = 25? note 1. test voltage must be applied within dv/dt rating. 2. this is static dv/dt. see figure 1 for test circuit commutating dv/dt is function of the load-driving thyristor(s) only. 3. all devices are guaranteed to trigger at an i f value less than or equal to max i ft . therefore, recommended operating i f lies between max i ft (15 ma for fodm3010 and fodm3021, 10 ma for fodm3011 and fodm3022, 5 ma for fodm3012 and fodm3023) and absolute max i f (60 ma). p arameter symbol value units total pa ckage storage temperature t stg -40 to +125 ? j unction temperature t j 125 ? operating temperature t opr -40 to +100 ? emitter continuous forward current i f (avg) 60 ma p eak forward current (1 ? pulse, 300 pps.) i f (pk) 1a reverse input voltage v r 3v po w er dissipation (no derating required over operating temp. range) p d 100 mw detector on-state rms current i t(rms) 70 ma (rms) off-state output terminal voltage fodm3010/1/2 v drm 250 v fodm3021/2/3 400 po w er dissipation (no derating required over operating temp. range) p d 300 mw p arameter test conditions symbol device min typ* max unit emitter input forward voltage i f = 10 ma v f all 1.20 1.5 v reverse leakage current v r = 3 v, t a = 25? i r all 0.01 100 ? detector p eak blocking current either direction rated v drm , i f = 0 (note 1) i drm all 2 100 na p eak on-state voltage either direction i tm = 100ma peak v tm all 1.7 3 v critical rate of rise of off-state voltage i f = 0 (figure 8, note 2) dv/dt all 10 v/? dc characteristics test conditions symbol device min typ* max unit led trigger current main terminal v oltage = 3v (note 3) i ft fodm3010 15 ma fodm3021 fodm3011 10 fodm3022 fodm3012 5 fodm3023 holding current, either direction i h all 300 ? characteristic test conditions symbol device min typ* max unit steady state isolation voltage (1 minute) v iso all 3750 vrms
3 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers t ypical performance curves fig. 1 led forward voltage vs. forward current fig. 2 leakage current vs. ambient temperature fig. 3 holding current vs. ambient temperature fig. 4 trigger current vs. ambient temperature i f - forward current (ma) 110 100 v f - forward voltage (v) 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.8 1.7 t a = -40 c t a = 25 c t a = 100 c t a - am bient temperature ( c) -40 -20 0 20 4 06080100 i drm - le akage current (na) 0.1 1 10 100 1000 vdrm = 600v t a - ambient temperature ( c) -40 -20 100 i h - holding current (normalized) 0.1 1.0 10 020406 080 normalized to t a = 25 c t a - ambient temperature ( c) -40 -20 0 20 40 60 80 i ft - trigger current (normalized) 0.8 0.6 0.8 1.0 1.2 1.4 1.6 v tm = 3v normalized to t a = 25 c 100
4 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers t ypical performance curves fig. 7 on-state characteristics v tm - on-state voltage (v) -4 -3 -2 -1 0 1 2 3 4 i tm - on-state current (ma) -800 -600 -400 -200 0 200 400 600 800 t a = 25 c fig. 5 led current required to trigger vs. led pulse width fig. 6 off-state output terminal voltage vs. ambient temperature pw in - led trigger pulse width ( c) 110 100 i ft - led trigger current (normalized) 0 2 4 6 8 10 12 t a in >> 100 s normalized to pw a t= 25 c a normalized to t = 25 c t a - ambient temperature ( c) v drm - off-state output terminal voltage (normalized) 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 -40 -20 020406 080100
5 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers t ypical performance curves figure 8. static dv/dt test circuit figure 9. resistive load vdc 400v (fodm302x) 250v (fodm301x) r = 10 k ? c test x100 scope probe pulse input mercury wetted relay 252 v (fodm302x) 158 v (fodm301x) 0 volts applied voltage wa veform v max = dv/dt = 0.63 v max = 252 r test d.u.t. d.u.t. rc rc rc figure 10. inductive load with sensitive gate triac (i gt 15 ma) v cc r in 1 2 4 3 0.1 f 180 c1 2.4k z l 120 v 60 hz moc3010 moc3011 moc3012 v cc r in 1 2 4 3 120 v 60 hz 180 r l fodm3010 fodm3011 fodm3012 400 v (fodm302x) = 250 v (fodm301x) (fodm302x) = 158 rc (fodm301x) 1. the mercury wetted relay provides a high speed repeated pulse to the d.u.t. 2. 100x scope probes are used, to allow high speeds and v oltages. 3. the worst-case condition for static dv/dt is established by triggering the d.u.t. with a normal led input current, then removing the current. the variable r test allows the dv/dt to be gradually increased until the d.u.t. continues to trigger in response to the applied voltage pulse, even after the led current has been removed. the dv/dt is then decreased until the d.u.t. stops triggering. rc is measured at this point and recorded. note: this optoisolator should not be used to drive a load directly. it is intended to be a trigger device only.
6 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers figure 12. typical application circuit v cc r in 1 2 4 3 0.05 f 0.01 f load 360 39 470 240 vac hot ground fodm3021 fodm3022 fodm3023 figure 11. inductive load with sensitive gate triac (i gt 15 ma) r in v cc 1 2 4 3 0.2 f 180 c1 1.2 k z l 120 v 60 hz fodm3010 fodm3011 fodm3012 in this circuit the ?ot side of the line is switched and the load connected to the cold or ground side. the 39 ohm resistor and 0.01 ? capacitor are for snubbing of the triac, and the 470 ohm resistor and 0.05 mf capacitor are for snubbing the coupler. these components may or may not be necessary depending upon the particular and load used.
7 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers ordering information marking information option description v vde approved r1 tape and reel (500 units) r2 tape and reel (2500 units) r3 tape and reel (500 units; unit 180?rotated) r4 tape and reel (2500 units; unit 180?rotated) r1v tape and reel (500 units) and vde approved r2v tape and reel (2500 units) and vde approved r3v tape and reel (500 units; unit 180?rotated) and vde approved r4v tape and reel (2500 units; unit 180?rotated) and vde approved 1 2 6 4 3 5 de?itions 1f airchild logo 2d e vice number 3 vde mark (note: only appears on parts ordered with vde option ? see order entry table) 4 one digit year code 5t wo digit work week ranging from ?1 to ?3 6 assembly package code 3011 x vm yy
8 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers d d w k t d 1 0 p p a p 0 b 0 0 2 e f w 1 0 r1 reel diame ter r2 devices per reel max. compon ent rotation o r tilt cover ta pe thickness cover tape width poc ket hole dia. pocket dime nsion pocket location sprocket hole location sprocket hole dia. sprocke t ho le pitch tape th ickn ess pocke t pitc h tape wid th symbo l de scription r1 r2 b d w 1 d k 0 1 0 e a p 0 p f 2 d p 0 0 t w 178 mm (7") 330 mm (13") dime nsions (mm) 12.00 0.4 7.30 0.20 20 ? ma x 5 00 1.55 0.20 2 .30 0 .20 0.065 0.02 9 .2 0 1.75 0.20 8.00 0.2 0 2.00 0.20 5 .50 0 .20 4.40 0.20 1.55 0.20 4.00 0.20 0.30 0.20 2 .54 pitch 2500
9 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers footprint drawing for pcb layout recommended infrared re?w soldering pro?e 0.024 ( 0.61 ) 0.100 ( 2.54 ) 0.060 ( 1.52 ) 0.310 ( 7.87 ) 0.190 ( 4.83 ) ? peak reflow temperature: 230? (package surface temperature) for 30 seconds ? time of temperature higher than 210?: 60 seconds or less ? one time soldering reflow is recommended (heating) to 30 s to 60 s 90 s time (s) pa c kage surface temperature t (?) 150 s 60 s 180? 230? (peak temperature) 210?
10 www.fairchildsemi.com fodm3010, fodm3011, fodm3012, fodm3021, fodm3022, fodm3023 rev. 1.0.0 fodm30xx 4-pin full pitch mini-flat package random-phase triac driver output optocouplers disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. the following are registered and unregistered trademarks fairchild semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. life support policy f airchild?s products are not authorized for use as critical components in life support devices or systems without the express written approval of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. product status definitions definition of terms datasheet identification product status definition advance information preliminary no identification needed obsolete this datasheet contains the design specifications for product development. specifications may change in any manner without notice. this datasheet contains preliminary data, and supplementary data will be published at a later date. fairchild semiconductor reserves the right to make changes at any time without notice in order to improve design. this datasheet contains final specifications. fairchild semiconductor reserves the right to make changes at any time without notice in order to improve design. this datasheet contains specifications on a product that has been discontinued by fairchild semiconductor. the datasheet is printed for reference information only. formative or in design first production full production not in production isoplanar? littlefet? microcoupler? microfet? micropak? microwire? msx? msxpro? ocx? ocxpro? optologic ? optoplanar? p acman? pop? power247? poweredge? f ast ? f astr? fps? frfet? globaloptoisolator? gto? hisec? i 2 c? i-lo ? implieddisconnect? intellimax? rev. i16 acex? activearray? bottomless? build it now? coolfet? crossvolt ? dome? ecospark? e 2 cmos? ensigna? f act? f act quiet series? powersaver? powertrench ? qfet ? qs? qt optoelectronics? quiet series? rapidconfigure? rapidconnect? serdes? silent switcher ? smart start? spm? s tealth? superfet? supersot?-3 supersot?-6 supersot?-8 syncfet? tinylogic ? tinyopto? trutranslation? uhc? ultrafet ? unifet? vcx? wire? across the board. around the world.? the power franchise ? programmable active droop?
|
